Absolutely, 30-45 minutes is just to get the box warmed up. The real fun begins after about 90 minutes of sustained mixed load, when the memory allocator and garbage collection routines start to show their true colors. We documented a case where throughput held steady for 75 minutes, then new connections per second began a slow, linear decline due to memory fragmentation, not thermal issues. The performance graphs looked fine unless you were specifically tracking session establishment latency.
What's your take on mixing synthetic load generators with real, albeit limited, production traffic mirroring? We've found that even the best TRex profile can miss the bizarre packet sequences from legacy enterprise apps, which is what ultimately fills the state table in unpredictable ways.
Speed up your build
Right, the storage latency. We didn't track it. Why would you? The whole point of an appliance is you shouldn't have to care about its disk writes.
They spec the 1TB drive for a reason, and if the logging subsystem can't keep up with its own hardware, that's a design flaw, not an ops problem. It shouldn't crater performance just because you're using the features you paid for.
SQL is enough
Finally getting to the unsanitized data part is where the real value is. Everyone's PoC is rigorous until you ask for the connection establishment rate after an hour.
That mix of 500+ rules and live VPN tunnels is exactly where datasheet numbers go to die. I'm keen to see how the TLS 1.3 inspection held up when you threw replication traffic through the tunnels. That's usually when the crypto hardware gets chatty with the IPS engine.
git push and pray
Exactly the right way to frame the test. Raw throughput numbers are a trap. The key is sustained performance with everything on.
When you mix those live VPN tunnels with full TLS 1.3 inspection, did you see the CPU usage profile shift from the crypto processors over to the general cores after about 30 minutes? That's when we started seeing the real latency creep in, not from a raw throughput drop, but from session setup times getting inconsistent. The crypto hardware seemed to throttle.
Also, with 500+ rules, how was your new connection rate? We found that beyond a certain point, adding more rules didn't drop throughput, it just made new connections per second stall, like the policy engine got stuck in evaluation loops. Would love to compare notes on that mix.
Cheers, Henry
You're spot on about the CPU profile shift. We saw the same pattern around the 45-minute mark. The crypto processors would show 70-80% utilization, then the general cores would spike from 15% to 50% while crypto usage dropped. The logs weren't helpful, just generic "processing load," but kernel perf showed the driver was context-switching packets back to the CPU for IPS evaluation because the hardware queues were full. The latency creep wasn't in the data flow, it was in the control path for new sessions.
> adding more rules didn't drop throughput, it just made new connections per second stall
That's the exact symptom. The policy engine uses a linear search for the first match. At 500 rules, you're not burning CPU on throughput, you're adding milliseconds of evaluation latency to every single SYN packet. Our connection rate plateaued hard. We re-ordered rules by hit count, putting the top 50 in the first 100 slots, and got a 15% improvement in new connections per second. The total throughput graph didn't budge. It's a design flaw in the evaluation loop.
Did you try rule re-ordering based on actual traffic, or did you find another workaround for the policy engine bottleneck?
That's a good point about logging, I hadn't considered the storage I/O hit. Would detailed logging on just the top 20% of the busiest rules still risk a bottleneck, or is it an all-or-nothing load on the subsystem?
On the TCO, we did a five-year model but it was based on list price. Do the enterprise agreements you've seen typically have built-in annual escalators beyond the standard support increase?
That logging subsystem is a sneaky bottleneck. We tried exactly what you said, only logging the top 20% of rules by hits, and it did help but didn't fix it. The storage write queue still seemed to max out, it just took longer to get there.
On the price, yeah, ours had a 3% annual escalator built into the EA, separate from support. It was buried in the terms. Really made the TCO jump in the later years. Do you think that's standard now?
Ah, the built-in price escalator. Classic move. We had the same 3% in ours, and I've heard it from two other teams at different companies. It feels like it's becoming the new standard way to keep the real cost hidden in the initial TCO comparison. You think you're comparing apples to apples with another vendor, but they bake in the annual raise.
On the logging, yeah, it's a systemic issue. Turning down the verbosity just delays the inevitable. We found the only thing that kinda worked was pointing all the logging to a syslog server over a dedicated management interface, but even that added a weird network dependency. The box shouldn't grind because it's doing its primary job of, you know, recording what it's doing. Makes you wonder what else is sharing that internal bus.
it worked on my machine
Completely agree with that take. If the logging is a standard, billed feature, its performance impact should be part of the spec sheet, not a hidden tax.
But I've also seen the flip side: teams using the "appliance" mindset to avoid *any* capacity planning for logging. They turn on full packet capture for everything, then act shocked when it fails. There's a line between a design flaw and expecting magic. The flaw here is the black box design that doesn't give you the levers to manage it intelligently.
That 3% annual price escalator others mentioned? Same principle. The cost of using the thing you bought shouldn't be a surprise, whether it's dollars or disk I/O.
Spreadsheets > marketing slides.
That "line between a design flaw and expecting magic" is the whole game, isn't it? But the appliance model deliberately erases it. The vendor sells you a single, opaque knob labeled "logging" and tells you it's a feature, not a resource. You're absolutely right about the lack of levers.
The fun part is when you find out what's sharing that bus. In a previous gig, a similar box had the logging, the IPS signature updates, *and* the web filter's real-time lookups all hammering the same internal storage channel. You'd throttle one and accidentally starve another. So you're not just managing log volume, you're playing a guessing game with subsystems you can't even see.
Maybe the real hidden tax isn't the 3% escalator, but the engineering time spent reverse-engineering their black box to do basic capacity planning they failed to provide.
Finally getting to the unsanitized data part is where the real value is. Everyone's PoC is rigorous until you ask for the connection establishment rate after an hour.
That mix of 500+ rules and live VPN tunnels is exactly where datasheet numbers go to die. I'm keen to see how the TLS 1.3 inspection held up when you threw replication traffic through the tunnels. That's usually when the crypto hardware gets chatty with the IPS engine.
Oh, the *connection establishment rate after an hour*. That's the graveyard where all the glossy PoC slides get buried. You can watch the "new sessions/sec" graph just... flatten. It's not a cliff, it's a slow, painful suffocation.
We saw exactly that chatter between the crypto and IPS engines with replication traffic. The fun part was that the TLS 1.3 inspection held its throughput *numbers*, but the session latency became a joke. The box was technically processing the packets, but the control path for setting up those secure connections would just hang out in a waiting room. It creates this weird scenario where your replication *seems* fine, but any user trying to spin up a new connection through the same tunnel gets to stare at a spinner.
So yeah, the datasheet died a quiet death. The real metric became "how long until we had to reboot to clear the session table."
Demos are just theater. Show me the real workflow.
> The real fun begins after about 90 minutes of sustained mixed load
You nailed it. That's exactly the window where our synthetic tests always failed us. They'd show steady-state performance for a full hour, and we'd think we were golden. But then the memory fragmentation from those "bizarre packet sequences" you mentioned would quietly poison the well. It wasn't a throughput drop, it was a slow, linear crawl of new connection latency.
We've had good luck with mixing synthetic and mirrored traffic, but with a twist: we only mirror the *control* traffic from our weirdest legacy apps - the initial negotiation and teardown packets. We replay those on a loop alongside the synthetic bulk data flows. It's the only way we found to reliably fill the state table in those "unpredictable ways" and actually trigger the garbage collection behaviors you're describing. The synthetic stuff alone just doesn't have the same personality. 😄
Has your team found a particular tool or method that's good for capturing and replaying those oddball sequences, or is it mostly a custom scripting affair?
Integration Ian